Saturday, August 20, 2016

✧・゚Sheryl Nome close-up ・゚✧

Here's a little close up on all the pieces I made for Sheryl Nome's Iteza gogo kuji Don't be late costume:

✧Jacket✧

(excuse the un-ironed hem ;___;)

The Jacket is made out of polyester fabric. It is fully lined. There is also shoulder padding added to give this jacket a more structured look. The buttons on the front are fully functional and there is also couple sew-on snaps to old the front panel. The buttons on the cuffs are only for decoration. There is only couple darts in the whole jacket: two next to the front panel, one in the middle of the back piece and two on the sides of the jacket. The decorations on the shoulders is sewn on by hand.
  
shoulder decoration
one of the snaps

Pants


The Pants are made out of same material as the jacket. They are fully lined. There are seams on the side of the pants as well as on the widest part of the pants. There is also wire added to the widest seam to make the pants stay wide while wearing them. The waistband of the pants has Velcro. I'm quite happy how these turned out, since i'm not too familiar with making pants. 



✧Undergarment

The undergarment has four pieces, two of which are visible while wearing (shorts and collar) and two of which are hidden under the jacket (suspenders and top). The suspenders are made out of elastic band and there are buttonholes, so it is possible to wear the shorts without suspenders. The top and shorts are made from faux leather. Both of them have a zipper on the side. I made the top a little wider than it is supposed to be :P

✧Hat


I'm not too happy with the hat. It came out too wrinkly and the cap is a little too big... But I really do like all the decorations and how the hat looks with everything. The Hat has eaten a lot of craft foam to keep the wanted shape. And it is fully lined. The decorations are made out of craft foam and worbla.




✧Belt, gloves etc.. 

The Belt is made out of faux leather, wire, craft foam and worbla. It doesn't have any darts and the buckle can be taken off. 

Gloves are made out of stretchy cotton. There is decorative button sewn on. 



earing

Tuesday, August 2, 2016

Sheryl WIP 2

The jacket was quite easy to make. I made the patterns using mannequin, which is not something I usually do. I wanted the jacket to have only one short seam on the front  and It would have been hard to make without the mannequin. Overall I'm quite pleased how the pattern came out. 
patterns for the collar front back and sleeve. Though I ended up changing the collar a lot. 
I put some interfacing on the upper back of the jacket and also to the front panels and then just sewed the blue parts of the jacket together. as simple as that. Then I sewed together the lining. At this point I had to make the collar and the cuffs. the Cuffs were easy to make but the collar was a little more troublesome. First I made it as the pattern above suggest... But it didn't work out. Then I curved it.. and It was too flat. Then  I added a narrow straight rectangle between the curved collar and the neckline. And that worked out! and interfacing is put on the lining at the cuffs and the collar.


After the collar was sewn in place I pinned the lining to the blue fabric and stitched them together close to the edge. Then I added yellow bias tape to finish the hem. After that I attached the cuffs to the jacket and added bias tape to them as well. After that I made buttonholes and added buttons. And made all the other tiny finishing  touches by hand.


Tadah!
pretty cuffs :3
The pants/legwear kinda just came together without any problems. I made lining to them as well and I had to add wire to make them hold the shape I wanted.
Lining and blue part.
Wire being added to the seam. It is sewn on the seam allowance
I made a lot of stitching into these, like this perfect stitching which was easy to make....
....and this a little harder stitching to make.

And this is how everything looked laying flat on the floor.. without bias tape and cuffs

The gloves I made using a pattern I found from here. It worked quite well, except the fingers were a little bit too long for my hands.

The belt was made from a faux leather and since it had a little stretch, I didn't have to add any darts to make it fit better. Because I didn't find closure big enough I decided to add boning to the front of the belt. So there's two rigile boning to hold the fabric. 

not too neatly sewn, but there will be buckle to hide all the mess.

The buckle belt I made by sandwiching worbla and craft foam and curved the creation a little. I added wire to the back to make it possible to add to the belt. The decorations for the hat were made with craft foam and worbla. I coated all the pieces with wood glue and then spray painted them. After that I added some highlights with black and white acrylic colors.

I heated the worbla a bit, placed craft foam pieces, added worbla to the top and trimmed the excess.

Then I made the wirethingies and attached them to the back of the buckle with wirblapieces.
sketch, stencil and cut pieces from craftfoam.

waiting for wood glue and paint 
The hat didn't work out as I wanted. I first tried to make it more triangle, but ended up making it round. Then I had to add support to the front to make it stay up and I also added some cotton wool to make it hold the shape better. I'll make another post on the details later~

The first versions patterns...